Metal
Straight Register Boot
A straight register boot or PH1 is a major component of an excellent ductwork system. The boot can be fastened to other ducts, including ceiling and wall units, using a nail and screw. Expect to spend about 20 minutes or less installing register boots. Airtight gaskets in the products reduce and eliminate leaks in heating, ventilation and air conditioning (HVAC) systems. These leak stoppages save you money and lower energy consumption. Straight collars and wider and narrower straight boots can be used to meet your HVAC design needs. Narrower boots start at 8-5″ with wider boots going up to 14 inches.
90 Deg Register Boot
A 90 deg register boot or PH2 is made to easily transition airflow from a round flexible or hard duct to a reactangular register or vent. The Longer kneck allows you to install easily in the ceiling or wall and easily connect your round duct. The airtight design also improves your heating, ventilation and air conditioning (HVAC) system’s overall performance quality. A reinforced mud ring allows for a durable fit. For smaller jobs, there are the 3 1/4 x 8-5″ through 14-8″ boots. Larger jobs may call for 4 to 6 x 10-4″ through 14-8″ 90 deg boots.
End Register Boot
End register boot or PH3 products are used to transition or connect rectangular and round sheet metal ductwork. For example, you can use an end register boot to connect a round sheet metal pipe to a rectangular wall stack. Whether you are building a brand new structure like a home or office complex or remodeling an existing facility, you can use the products to build out or improve upon existing standard heating, ventilation and air conditioning (HVAC) systems. Products are available in a range of sizes from 8-5″, going up to 14-7″. The durable metal and aluminum products hold up well beneath low to medium pressure.
Snap Tab Duct Board Collar with Gasket
- Features a hem on top of collar, removable round punch-out tab for damper assembly, and 1 1/4″ double-click tab for easy assembly
- For use with HVAC
- Manufacturer may vary based on your location
Galvanized Steel sizes 4” to 20”
Sheet Metal Duct End Caps
Sheet Metal Duct End Caps are the perfect sheet metal duct fitting to use when you terminate a duct run. All End Caps are manufactured from the highest of quality galvanized steel. They are perfect for maintaining a professional look, especially if your duct system is exposed.
Flat Airtight
This flat airtight takeoff has a 26-gauge damper with an 18-gauge handle secured with a wingnut with a locking handle.
- 5-3/4 in. tube length
- 1-1/2 in. crimp length
- 4 pre-drilled screw holes
- Available in 4” to 20”
Manual Dampers
Galvanized Sheet Metal Round volume dampers have manual quadrant adjustment handle. The ideal use is in branch duct lines for adjusting supply or return air volume. They are field installed into sheet metal starting collars or register boots. Can be used for Remodeling, Do it yourself and New Residential projects. These round duct volume dampers slide into ducting & have a manual handle that screws on. Used for air flow control and routing. Duct dampers prevent reverse air leakage in your metal duct lines. These dampers are made from high quality steel and are designed for vertical or horizontal mounting. The damper blades are lightweight yet sturdy for easy opening and closing. They can be used for bathroom fans, kitchen vents and a wide range of hvac uses. The dampers install inside the circular ducting to prevent a backdraft of air. Available sizes vary by product but we generally stock 3″ 4″,5″,6″, 7″,8″,9”,10″,12″,14”,16”,18” sizes.
KD pipe
Our Galvanized Sheet Metal Duct, or sometimes referred to as KD pipe is manufactured from high quality galvanized steel in convenient 3 to 5 foot lengths ranging for 4” to 20” round for easy handling. KD is referenced to “knock down” because upon installation the pipes seam is left open for cutting and fitting to your application such as vent piping and appliance, water heater or furnace. Once you snap the pipe together the connection is permanent. The connection of the sheet metal pipe is crimped for easy fitting of consecutive duct joints or to sheet metal fittings and Flexible duct. The seam on our galvanized sheet metal duct is formed on a snap-lock machine which allows ease of assembly on your job site. Just simply snap the seam together and install to your adjoining items.
Duct Reducers
Duct Reducers are the HVAC ducting fitting to use when you need to change from one size duct to another size. All of our Reducers are manufactured from the highest quality galvanized steel. They are perfect sheet metal fittings for maintaining maximum airflow through your system while changing to the needed duct size to get into tighter spaces.
AirTite Adhesive Saddle Takeoff W/O Damper
Snap-Rite – AirTite Adhesive Saddle Takeoff W/O Damper
AirTite Adhesive Saddle Takeoff, W/O Damper.
- Adhesive to seal around the duct.
- Available in sizes 4” to 16”
Single Wall Elbows
Our HVAC adjustable 90 Degree elbows are are used to make turns in runs of round pipe and flexible duct from O (straight) to 90 degrees. They are also crimped on one end to easily fit into a pipe or duct fitting of the same diameter. They have a sturdy galvanized steel construction and are simple to adjust, and fabricated from premium G60 galvanized steel. They are the fitting to use when needing to make tight corners and are utilized for maintaining the best airflow for maximum efficiency in your HVAC system. These elbows are made of 26 gauge galvanized sheet metal up to 12″ or 24 gauge galvanized sheet metal from 14″ to 24″. Ideal application with either flexible duct or sheet metal duct.
Wyes
Wyes are the fitting to use when you need to branch off your duct run to a smaller size. The sizes are listed for the inlet side, the discharge side and then the branch side. All wyes are manufactured from the highest quality galvanized steel. They are perfect fittings for maintaining maximum airflow through your system while branching off to multiple locations.
